Source This Article

They are making a few great observations regarding Tools You Need to Install a New Bathtub as a whole in the content down the page.

Mounting a bathtub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately hard task. If the old tub is readily available, the task can relocate quickly; if you need to open a wall to get rid of the old bathtub and position the new tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub and also set in the new one. Make certain you have qualified yourself for the job and fit trying it. Rather than employing a professional to take over a halfway-completed project, it is better to think about using one prior to you begin. Chances are you may require an expert plumber to make tube links.
This write-up will help you install a new tub in your bathroom if you have already acquired a brand-new bathtub and don't need to alter the arrangement of your previous water system pipes.
Your devices and also product list need to consist of the following:

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Preparing for the Installation

First of all, the sustaining structure provided with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last setting.

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be rather bothersome as a result of the limited gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly originate from the pipes. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Before going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.

Mounting the Bathtub

Making use of both wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub till the level reviews degree.
To mount faucets, fit the bottom of the furthest adaptable tap port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water system and also inspect all joints and brand-new pipework for leakages and also tighten them if essential. Load the bathtub and also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub ought to wait until the bath tub has actually been used a minimum of once as this will certainly resolve it into its last setting.

Fitting New Taps

If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washers remain in area in between the tap and the sink. Secure the faucet in place with the producer offered backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Tub

In the location where the bathroom meets the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bath and also the tiling, leading to complications with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can split rather early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles utilizing waterproof or water-proof glue and also grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you enjoy reading up on How to Install a Bathtub? Post feedback directly below. We will be delighted to find out your reactions about this page. Hoping that you visit us again later on. Liked our write up? Please share it. Let other people locate it. Bless you for your time. Don't hesitate to come visit our blog back soon.

Book Now